![]() If you plan to use SSL with NZBGet use this cipher RC4-MD5 recommended by hugbug the developer of this fine software. Reboot to make sure NZBGet starts on boot sudo reboot See if the nzbget service works sudo service nzbget start Note: if you are on Raspbmc remove the setuid and setgid lines (thanks to Raijmond) #description "NZBGet upstart script" Paste this code and save the file with Ctrl+X, Press y and then Enter Install upstart if you understand the risks! sudo apt-get install upstartĬreate the NZBGet upstart file sudo nano /etc/init/nf Scroll to the bottom for further configuration and tweaks. This command adds a cronjob to start nzbget every time it boots if the init.d script isn't doing the job crontab -l | | crontab. Reboot to test, if it will only work once the system has been up you can use a cronjob in conjunction with the init.d script. Update the system to start NZBGet on boot sudo update-rc.d nzbget defaults Make the NZBGet init.d script executable sudo chmod +x /etc/init.d/nzbget # Description: starts instance of NZBGet using start-stop-daemon ![]() # Short-Description: starts instance of NZBGet # Required-Stop: $local_fs $network $remote_fs # Required-Start: $local_fs $network $remote_fs Paste this NZBGet init.d script #!/bin/sh ![]() Use Ctrl+W to find DaemonUsername=root and change it to DaemonUsername=piĬreate the init.d script sudo nano /etc/init.d/nzbget NZBGet init.d ScriptĮdit your NZBGet configuration sudo nano /home/pi/.nzbget The upstart script is more reliable but can cause other issues.įor either of these methods your path may be /usr/bin/local if you built from source so adjust as necessary. You can use an init.d script or upstart script. Now try and access NZBGet at username:nzbget password:tegbzn6789 Autostart NZBGet on Boot Note: For the Raspberry Pi the extra / is necessary after scripts (this may no longer be true) Note: Your extension scripts folder is /path/to/scripts/ which you set in NZBGet Settings -> Paths -> ScriptDir Unpack the VideoSort Script unzip videosort-ppscript-5.0.zip Install the Videosort post processing script to have NZBGet sort your video media automatically, if you are using CouchPotato you don't necessarily need this but it is useful if you are sending movie nzbs straight from your indexer to NZBGet.Ĭreate an NZBGet scripts folder mkdir -p /path/to/scripts & cd /path/to/scripts When the build is done you should change the permissions of the configuration file sudo chown pi:root /usr/local/etc/nf Install VideoSort You can now detach from the screen with Ctrl+A, then D (for detach) and close your Putty SSH session, it will still build.Ĭheck on the NZBGet build process with screen -r This also takes a good 20 minutes./configure -with-tlslib=OpenSSL & make & sudo make install & sudo make install-conf Open a new screen session, press space twice to get through the messages screenĬompile, install and create the configuration file for NZBGet 14.x. ![]() We are going to run screen so that it compile in the background sudo apt-get install screen -y Unpack the source and enter the folder it creates tar -xvf nzbget-14.2.tar.gz & cd nzbget-14.2 Install dependencies and screen for compiling in the background sudo apt-get install build-essential libsigc++-dev sigc++ libncurses5-dev libssl-dev libxml2-dev unzip p7zip-full ncurses-dev openssl screen -y If you didn't have issues scroll down to make NZBGet autostart on boot. If you have issues with the above process you will have to build NZBGet from source. Try browsing to the IP address of your Pi at the default username is nzbget and default password is tegbzn6789 Run NZBGet to make sure it works nzbget -D Install NZBGet sudo apt-get install nzbget -yĬopy the default NZBGet configuration file sudo cp /usr/share/nzbget/nf ~/.nzbgetĬhange ownership of the configuration file to avoid permission issues sudo chown pi:root ~/.nzbget Gpg -a -export 0E50BF67 | sudo apt-key add -Īdd Mike's repo with this command echo "deb wheezy main" | sudo tee -a /etc/apt/sources.list It also solves Unrar error 64 as long as you are using absolute paths in NZBGetĪdd these magic keys to authenticate with his repo gpg -recv-keys -keyserver 0E50BF67 If the precompiled package doesn't work you can build from source sudo apt-get install build-essential -y Install the unrar package sudo dpkg -i unrar_5.2.6-1.arm6_b You can install this unrar package that is precompiled for the Raspberry Pi wget Install NZBGet 14 Raspberry Pi with Raspbian
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |